Chimera7 Pro HD 6S Long Range BNF Quadcopter w/ Caddx Air Unit

Introducing the iFlight 7.5 inch long-range FPV long range drone! This beast is kitted out with a 7.5-inch carbon fiber frame and 2809 2300KV brushless motors. The 7.5-inch props give you maximum thrust and efficiency, and the 1250kv motors are powerful enough to punch through even the toughest of winds.

GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).

The Caddx air unit comes pre-installed. If you are using the DJI Remote, then it is bind and fly. Otherwise if you plan to use another receiver such as TBS crossfire, you will need to install this yourself (there is mounting space for this however)

Main Changelog from Chimera7 to Chimera7 Pro:

– SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)

– New Lightweight Side Panels Design – Keep Your Rig Clean

– XING 2806.5 upgraded to XING2 2809 1250KV

– 7-inch frame upgraded to 7.5inch

Features

– Battery voltage LED status light (illuminated IF logo on the bottom)

– 360 TPU protection, DJI cam protection and antenna mounts

– GoPro TPU bottom stand (GoPro protector not included)
– Lightweight Side Panels Design – Keep Your Rig Clean

– No props in view (DJI Air unit record in 1080p/60fps)
– XING2 2809 1250KV efficient wide stator motors

– GPS pre-installed for more safety at a distance

– 6mm rigid arm design for more stiffness

– Top- and bottom battery mount option

Pre Tuned and Setup

• Pre tuned by Iflight, a general PID- and Filter tuning was applied for a great flight experience!
• To restore lost tunes or updates, please check out Iflight CLI FIrmware settings here
• Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn’t end in a mess!
• GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour as this is still an experimental feature. Please see our article on how to enable GPS rescue mode

Specifications

– Weight: 695g (without battery and GoPro mount)

– Total Dimensions: 258*200mm (body dimension)

– Upper(middle) Plate Thickness: 3mm

– Bottom to Top Distance: 20-29mm

– ESC: BLITZ E55 4-IN-1 2-6S ESC

– Camera Plate Thickness: 3mm

– Bottom Plate Thickness: 3mm

– Top Plate Thickness: 3mm

– Geometry: DC (DeadCat)

– HQ 7.5X3.7X3 Propellers

– Arm Thickness: 6mm

– XING2 2809 1250KV

– Wheelbase: 321mm

– FC: BLITZ F722

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)

FC //BLITZ F722 Flight Controller

• Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
• Smartaudio / IRC Tramp VTX protocol supported
• Firmware target: IFLIGHT_BLITZ_F722
• Motor outputs: 4x (SH1.0 connector)
• Flash: 32MB (Blackbox flash)
• I2C serial: SDA / SLA pads
• Dimensions: 36.5*35 mm
• Barometer: DPS310
• OSD Chip: AT7456E
• LED controller: Yes
• MCU: STM32 F722
• Beeper pad: Yes
• Gyro: BMI270
• Weight: 7.8g
• UARTS: 6

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

• Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
• Mounting Holes: 30.5*30.5mm/4mm
• Target: IFLIGHT_BLITZ_G2
• Supports 2-6S Lipo input
• Current sensor: Yes
• Constant: 55 Amps
• Current rate: 200
• Burst: 65 Amps
• Weight: 15.3g
• MCU G071
• BEC: No

Included

• 4 x HQ 7.5X3.7X3 CW propeller + 4 x HQ 7.5X3.7X3 CCW (Color may vary)
• 2 x Albatross LHCP 5.8GHz SMA FPV Antenna
• 2 x iFlight Lipo Strap 20*250mm (Black)
• 1 x Pre-built and Tested Chimera7 Pro

Note:

All iFlight BNFs are tested before shipment to guarantee the highest quality.

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com .

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support .

Includes

Pre-built and indoor tested Quadcopter

• 1x Chimera7 frame
• 1x GoPro TPU bottom stand incl. lock screw
• 1x DJI FPV camera
• 1x DJI FPV Air Unit Module
• 2x Albatross LHCP RP-SMA 5.8g 150mm antenna
• 2 sets x Gemfan tri-blade 7040 props (Set of 4 – Color may vary)
• 4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)