DJI Mic Mini Transmitter (Infinity Black)
$33.99$27.19
- Email: [email protected]
$34.99
$27.99
This 4.2" e-Paper module is a quad-colour display (Red/Yellow/Black/White) with no backlight and keeps the last displayed image for long periods even when powered off. Power is only needed during refreshes, so you're barely using any power. The display also has a wide 170 viewing angle for visibility from most angles.
The SPI interface lets it connect to other controller boards like Raspberry Pi and Arduino, while a built-in voltage translator provides compatibility with both 3.3V and 5V MCUs. Included are online development resources and a manual, which makes it easy to get started!
We also have the raw display panel here
Features
- No backlight, keeps displaying last content for a long time even when powered down
- Ultra-low power consumption, basically power is only required for refreshing
- Comes with online development resources and manual (driver board circuit diagram, examples for Raspberry Pi / Jetson Nano / Arduino / STM32)
- Adapting SPI interface for connecting with controller boards like Raspberry Pi / Jetson Nano / Arduino / STM32, etc.
- Voltage translator, compatible with 3.3V / 5V MCUs
Specifications
| Operating Voltage | 3.3V/5V |
| Interface | 3-wire SPI, 4-wire SPI |
| Outline Dimensions | 103 x 78.5 (mm) |
| Display size | 84.8 x 63.6 (mm) |
| Dot Pitch | 0.212 x 0.212 (mm) |
| Resolution | 400 x 300 pixels |
| Display Colours | Red/Yellow/Black/White |
| Greyscale | 2 |
| Full Refresh Time | 21s |
| Refresh Power | <30mW |
| Standby Current | <0.01uA (almost none) |
| Viewing Angle | >170 |
Resources
- Product Wiki
- Datasheet
Pinout
| VCC | Power (3.3V / 5V input) |
| GND | Ground |
| DIN | SPI MOSI pin |
| CLK | SPI SCK pin |
| CS | SPI chip selection, low active |
| DC | Data/Command selection (high for data, low for command) |
| RST | External reset, low active |
| BUSY | Busy status output pin |
Package Contents
- 1x 4.2" e-Paper Module
- 1x PH2.0 8-pin Cable
This 4.2″ e-Paper module is a quad-colour display (Red/Yellow/Black/White) with no backlight and keeps the last displayed image for long periods even when powered off. Power is only needed during refreshes, so you’re barely using any power. The display also has a wide 170 viewing angle for visibility from most angles.
The SPI interface lets it connect to other controller boards like Raspberry Pi and Arduino, while a built-in voltage translator provides compatibility with both 3.3V and 5V MCUs. Included are online development resources and a manual, which makes it easy to get started!
We also have the raw display panel here
Features
- No backlight, keeps displaying last content for a long time even when powered down
- Ultra-low power consumption, basically power is only required for refreshing
- Comes with online development resources and manual (driver board circuit diagram, examples for Raspberry Pi / Jetson Nano / Arduino / STM32)
- Adapting SPI interface for connecting with controller boards like Raspberry Pi / Jetson Nano / Arduino / STM32, etc.
- Voltage translator, compatible with 3.3V / 5V MCUs
Specifications
| Operating Voltage | 3.3V/5V |
| Interface | 3-wire SPI, 4-wire SPI |
| Outline Dimensions | 103 x 78.5 (mm) |
| Display size | 84.8 x 63.6 (mm) |
| Dot Pitch | 0.212 x 0.212 (mm) |
| Resolution | 400 x 300 pixels |
| Display Colours | Red/Yellow/Black/White |
| Greyscale | 2 |
| Full Refresh Time | 21s |
| Refresh Power | <30mW |
| Standby Current | <0.01uA (almost none) |
| Viewing Angle | >170 |
Resources
- Product Wiki
- Datasheet
Pinout
| VCC | Power (3.3V / 5V input) |
| GND | Ground |
| DIN | SPI MOSI pin |
| CLK | SPI SCK pin |
| CS | SPI chip selection, low active |
| DC | Data/Command selection (high for data, low for command) |
| RST | External reset, low active |
| BUSY | Busy status output pin |
Package Contents
- 1x 4.2″ e-Paper Module
- 1x PH2.0 8-pin Cable
0 reviews for 4.2″ ePaper Display Module – Red/Yellow/Black/White (400×300)
There are no reviews yet. Be the first to review this product!
Add a review
Your email address will not be published. Required fields are marked *